antos
Drag-strip hero
Posts: 298
|
Post by antos on May 14, 2017 11:04:45 GMT 1
Cheers mattπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 22:33:41 GMT 1
Nice 1 John , I bought mine from Martin at mad bike designs there made of billet alloy and are working fineπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 19:27:08 GMT 1
Hi John I thought them to be a bit stiff too when I replaced mine, but could turn them by hand no probs, as matt says moly grease on emπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 13:16:25 GMT 1
Just found it thanks, do you know if this would just be a straight swap over, no fowling from that nut on back of the ball?
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 13:05:37 GMT 1
Thanks mateπ I'll try to find them in his shopπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 13:04:34 GMT 1
You can buy an lc one Just cut a bit off the back of the peddle mount and use a pv connecting rod from Norbo or MB-designs Alternatively I've got loads Matt Thanks mattπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 13, 2017 10:58:20 GMT 1
Steve it's no longer available from Yamaha mate.
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 11, 2017 21:56:03 GMT 1
Many thanks steve it's appreciated mate π Antos
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 10, 2017 21:51:26 GMT 1
Ok thanks better think of something else then ha
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 10, 2017 9:45:48 GMT 1
I had exactly the same problem on my f2 I used ptfe and jobs a good un π
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on May 10, 2017 9:39:29 GMT 1
Hi lads, does anyone know if an lc 350 gearchange linkage will fit onto a powervalve f2 please? Cheers antos
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 30, 2017 22:01:26 GMT 1
Same here Steve had an rrw blade for 10 yrs then got a 2011 blade ( great bike) sold it last year as I was balls out every ride, got an f2 and love itπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 22, 2017 23:59:41 GMT 1
Hi Anthony , you need to ask this in the wanted section really mateπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 19, 2017 14:24:00 GMT 1
OMG I'm in love with that front end π
|
|
antos
Drag-strip hero
Posts: 298
|
Newbie
Apr 19, 2017 14:05:11 GMT 1
via mobile
Post by antos on Apr 19, 2017 14:05:11 GMT 1
Hi john and welcome ,great lads on here, prepare to spend a lot lol π
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 19, 2017 7:41:16 GMT 1
Seriously lads it's supposed to put less stress on hoses etc trouble is it's quite expensive π
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 17, 2017 23:11:33 GMT 1
Anyone using this? Just done my engine rebore / crank etc and thinking of putting it in . supposed to be less stresss on cooling system? Thanks antos
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 14, 2017 13:52:19 GMT 1
Kostas what paint did you use on the casings mate?
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 14, 2017 13:51:22 GMT 1
Went from this To this, Discovered that my cases were not holding pressure so it had to be done...
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 14, 2017 13:50:16 GMT 1
Broke down on way to squires That's where I was heading Saturday afternoon when I lost a full tank of juice and nearly binned it. Bike is in bits now. hi what paint did you use on the casings please? Thanks
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 14, 2017 11:14:19 GMT 1
Phew ,thanks steveπ Overthinking it Im afraid worrying too much.
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 14, 2017 9:08:42 GMT 1
Guys I've had my crank rebuilt at Grampian I'm just about to put it in and join cases but when I took off the timing side crank seal I've noticed some wear marks where it's been sat, now seen as I've pulled it apart as I'm sure this seal was gone in the first place, will I be ok to go just fitting a new gen yam seal? Grampian never mentioned it when they rebuilt it but did say I needed 2 new inner webs. What you think guys I'd be mighty annoyed if I put it all back together and it didn't seal. Thanks antos
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 13, 2017 10:21:03 GMT 1
Damn it I never even thought of that mattπ I did as you suggested on the wheel rims before I sprayed them, so I know that's the right way .doh π
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 12, 2017 22:41:17 GMT 1
Thanks very much Dave I appreciate thatπ Will do exactly that π
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 12, 2017 10:10:57 GMT 1
Cheers Shaun, I cleaned everything on the strip down and sprayed inside with gt85, but yes it makes you think it's the problem as holding it on they work.
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 12, 2017 9:30:39 GMT 1
Guys I've searched 5 pages of indicator problems and can't find an answer , can anyone help, all my indicators worked fine before my restore, so fitted new indicators from norbo wouldn't flash so put the correct 21 watt bulbs in them and they flashed π Next day tried them no flash, they now only flash when I hold the left handlebar switch against it's stop? Any ideas guys
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 12, 2017 9:07:46 GMT 1
Guys any tips on best and quickest way to polish up the ypvs lettering on cylinder head after it's been sprayed black? Thanks
|
|
antos
Drag-strip hero
Posts: 298
|
Case leak
Apr 10, 2017 23:10:40 GMT 1
via mobile
Post by antos on Apr 10, 2017 23:10:40 GMT 1
Cheers kostas I'll be rebuilding mine soon so I'll do thisπ
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 10, 2017 22:11:39 GMT 1
Didn't know you could do that bare, I've bought the valves now though
|
|
antos
Drag-strip hero
Posts: 298
|
Post by antos on Apr 10, 2017 17:25:01 GMT 1
Thanks mate π I know what you mean and they are a tad sloppy so guess it's more money on bushes Was hoping to get away with them 22k on the clock no grooves in them but a tad shiny as you say
|
|