|
Post by LC'Adam on Oct 27, 2010 20:27:39 GMT 1
Just got the last RD125LC Nikon race pipe ever to be made from Frank at Nikon today ;D ;D ;D It has been in storage sine 1992 (when the last batch was made). Had a go with a 170 main jet (standard is 155) and I also premix. However it is running lean on the 170 . Pulled in 1-4th to 12,000 rpm with tremendous power. But it just kept getting hotter and hotter. Only went 10 miles to test but it got too hot and lost some power so I had to stop to allow it to cool. Was amazed also to see the pipe had turned a bronzie/goldie color. Cases and rad felt normal temperature but cylinder and head were too hot. The end can was also very hot which again suggests it was lean. When i got it home I pulled the plug out and it was very light brown, no heat damage/oxidation but very light brown. I am also in need of a new exhaust gasket. So i have ordered a new copper type gasket and a 180 main jet. Which should cool it down and allow it to pull to the red in all gears I just hope the over heat has caused no permanent damage I also need to drain the fuel as I'm using really crap oil which won't be helping Castrol r40, 180 main, new gasket, new gear oil, washed air filter and new plug, then I will have abother go Adam
|
|
|
Post by twostroker on Oct 27, 2010 20:46:58 GMT 1
is your barrel tuned?
|
|
|
Post by LC'Adam on Oct 27, 2010 20:55:19 GMT 1
No mate standard 10w bore, 10w carb and standard air box
|
|
|
Post by LC'Adam on Oct 27, 2010 21:03:24 GMT 1
A vast amount more power than a micron, i couldn't belive it. and yes gaz, but my premixing must be leaning it way out. I will wack in a 180 and do a chop
|
|
|
Post by LC'Adam on Oct 27, 2010 22:33:53 GMT 1
On mums best rug ;D ;D ;D Will do a vid when its running nice Adam
|
|
|
Post by mellow on Oct 27, 2010 22:36:12 GMT 1
whens the micron being sold
|
|
|
Post by LC'Adam on Oct 27, 2010 22:39:44 GMT 1
I hope not gaz or I won't get any pocket money for ages ;D And mellow are you interested? lol
|
|
|
Post by mellow on Oct 27, 2010 22:40:43 GMT 1
depends
|
|
|
Post by LC'Adam on Oct 27, 2010 22:43:30 GMT 1
You know where my pm button is mells The buyer may want to consider changing the end can color though ;D I have the original silencer and stinger set up as well tbh (bit tatty)
|
|
|
Post by seanrd on Oct 28, 2010 12:34:03 GMT 1
I know its not the same but when i went from standard pipe to a swarbrick, open air box, mild tune and premix i had to go from a 170 jet to a 220. Runs lovely now, pulls clean revs out in every gear and plugs always a nice brown. TZR125 by the way
|
|
|
Post by looey on Oct 28, 2010 13:28:01 GMT 1
Just got the last RD125LC Nikon race pipe ever to be made from Frank at Nikon today ;D ;D ;D It has been in storage sine 1992 (when the last batch was made). Whatever you do........ don't bolt that NOS Nikon pipe on your 125LC, cos when you do it will no longer be NOS and will be second-hand like everyone elses ;D ;D Only kidding...... nice pipe that
|
|
|
Post by mellow on Oct 28, 2010 18:23:41 GMT 1
Question Why dont he make more as demand is there
|
|
|
Post by LC'Adam on Oct 28, 2010 20:26:11 GMT 1
No idea mellow, all he said to me was he didn't make chambers any more and if he were to it would be £350 +
|
|
|
Post by mellow on Oct 28, 2010 22:34:34 GMT 1
perhaps he has too much money
|
|
|
Post by mellow on Oct 31, 2010 9:49:42 GMT 1
i've got a nikon too now
|
|
|
Post by looey on Oct 31, 2010 10:17:10 GMT 1
£60 by any chance ?. Was watching it but don't want one
|
|
|
Post by mellow on Oct 31, 2010 15:34:05 GMT 1
|
|
|
Post by LC'Adam on Oct 31, 2010 17:17:21 GMT 1
Haha, Me, mellow and gaz. The Nikon boyz ;D ;D ;D
|
|
|
Post by mellow on Oct 31, 2010 22:42:11 GMT 1
wont see mine for a long time ;D
|
|
|
Post by LC'Adam on Oct 31, 2010 23:50:31 GMT 1
Nor mine mate lol, Bike is coming apart over the winter for some mods ;D
|
|
|
Post by mellow on Oct 31, 2010 23:55:21 GMT 1
prefer rock meself m8 ;D
|
|
corf
Drag-strip hero
Posts: 251
|
Post by corf on Nov 28, 2010 21:29:23 GMT 1
his he not trading as website still up and runing
|
|
|
Post by LC'Adam on Nov 28, 2010 21:34:08 GMT 1
He told me he dosn't make chambers any more, if he were to he would charge £300 +
|
|