|
Post by Yogi on Apr 7, 2024 14:02:18 GMT 1
Hi Gang Here we go again Parts already collected Twin discs a KTM left hand calliper and a few other parts Cheers Matt
|
|
|
Post by JonW on Apr 7, 2024 14:05:11 GMT 1
Excellent!
|
|
|
Post by urbantangleweed on Apr 7, 2024 14:10:02 GMT 1
That'll be an interesting one to see come up ππ»
|
|
|
Post by mouse on Apr 7, 2024 14:17:21 GMT 1
Ye-haa, nice one Matt!
Mouse
|
|
|
Post by dusty350 on Apr 7, 2024 19:43:57 GMT 1
Just seen this 5 hours late. You must have nearly finished it by now then Bout time you built another ! Looking forward to another stunner mate
|
|
|
Post by andy748 on Apr 7, 2024 19:50:31 GMT 1
Great start to the project, get cracking then. Andy.
|
|
|
Post by reedx on Apr 7, 2024 21:02:46 GMT 1
Looking forward to this one.
Colin
|
|
|
Post by donkeychomp on Apr 7, 2024 21:19:10 GMT 1
Off to get more popcorn!
Alex
|
|
|
Post by lcmarky on Apr 8, 2024 8:12:12 GMT 1
Fantastic - looking forward to this,
What's the spec'?
|
|
|
Post by midlifecrisisrd on Apr 10, 2024 8:47:55 GMT 1
Good start π
Now find that mojo, it will be under the bench somewhere π€£
I'm jealous, I'm away back to hanging doors π
Steve
|
|
|
Post by urbantangleweed on Apr 10, 2024 9:01:44 GMT 1
I'm jealous, I'm away back to hanging doors π What did they do to warrant such harsh punishment?
|
|
|
Post by midlifecrisisrd on Apr 10, 2024 10:22:23 GMT 1
I'm jealous, I'm away back to hanging doors π What did they do to warrant such harsh punishment? They drew the short straw, the floor is getting layed later π Steve
|
|
|
Post by urbantangleweed on Apr 10, 2024 12:02:14 GMT 1
What did they do to warrant such harsh punishment? They drew the short straw, the floor is getting layed later π Steve Watch out for splinters......
|
|
|
Post by abar121 on Apr 10, 2024 17:58:49 GMT 1
Loving this project. I have an SZR rear end, so looking forward to see how an expert mounts it up
|
|
|
Post by muttsnuts on Apr 10, 2024 19:22:53 GMT 1
come on, is it done yet ?
|
|
|
Post by mouse on Apr 11, 2024 18:59:26 GMT 1
We must have blinked, I think he's built it, painted it, advertised it and sold it!
Mouse
|
|
|
Post by abar121 on Apr 11, 2024 19:57:30 GMT 1
Has he got back from the woods yet?
|
|
|
Post by Yogi on Apr 12, 2024 17:47:32 GMT 1
Fantastic - looking forward to this, What's the spec'? Not sure on spec Marky π, Iβm winging it as usual π€£
|
|
|
Post by Yogi on Apr 12, 2024 17:49:07 GMT 1
Good start π Now find that mojo, it will be under the bench somewhere π€£ I'm jealous, I'm away back to hanging doors π Steve Looked under the bench π€£must be getting warmer now π
|
|
|
Post by Yogi on Apr 12, 2024 17:50:15 GMT 1
Loving this project. I have an SZR rear end, so looking forward to see how an expert mounts it up So am I mate πthen we can both copy him π€£π€£
|
|
|
Post by Yogi on Apr 12, 2024 17:51:49 GMT 1
come on, is it done yet ? It wouldβve been if I wasnβt waiting for you to develope the parts π€£π€£π
|
|
|
Post by Yogi on Apr 12, 2024 17:52:32 GMT 1
We must have blinked, I think he's built it, painted it, advertised it and sold it! Mouse Your right mouse. Iβm on to the next now π€£π€£
|
|
|
Post by Yogi on Apr 12, 2024 18:10:17 GMT 1
As you know Iβm not much of a writer but I have trimmed 11mm from both sides of the swinger The frame mounts were 208mm and the swinger 230mm. Iβve found and ordered some 37mm od x 22mm id bearings and an headstock set as well so at a standstill for now π MattπΆπ»πΆ
|
|
|
Post by Yogi on Apr 13, 2024 16:27:14 GMT 1
Bearings arrived midday so I set about it Bearings in and the swinger was on Only slightly jacked up and the SZR shock feels a bit stiff with no static sag Iβll wait until the lumps in before deciding if I need a softer one Matt πΆπ»πΆ
|
|
|
Post by andy748 on Apr 13, 2024 17:31:02 GMT 1
Looking good Matt, how did you cut the swinger? Cutting disc or ye olde hacksaw? Need to do my Fz600 swinger. Andy.
|
|
|
Post by Yogi on Apr 13, 2024 17:38:32 GMT 1
Looking good Matt, how did you cut the swinger? Cutting disc or ye olde hacksaw? Need to do my Fz600 swinger. Andy. Hi Andy I used a 1mm disc but left it slightly longer and filed it flat π Matt πΆπ»πΆ
|
|
|
Post by donkeychomp on Apr 13, 2024 21:26:40 GMT 1
That swinger is amazing.
Alex
|
|
|
Post by Yogi on Apr 14, 2024 6:06:18 GMT 1
That swinger is amazing. Alex Cheers mate, hopefully works out ok π
|
|
|
Post by Yogi on Apr 14, 2024 14:28:58 GMT 1
Rejigged the top mounts and now the suspension works as should Looks better with clothes on Matt π»πΆπΆ
|
|
|
Post by JonW on Apr 14, 2024 14:34:42 GMT 1
nice, fast, work Matt... as ever! Good to see a Thor hammer being used... best of British!
|
|